How To Make Ping Pong Paddle Sticky?

How To Make Ping Pong Paddle Sticky?
sportlifez disclosure

Stickiness is an essential factor that affects the accuracy of a ping pong paddle. Check out the article below to know how to make ping pong paddle sticky!

Checking the stickiness of a ping pong paddle

The method is simple. Put the rubber part of your ping pong paddle on the edge of an ordinary ping pong table with no glue involved.

Use a moderate force against the handle.

If it is not easy for the ping pong handle to come off the table, its stickiness is relatively high.

Otherwise, if the ping pong bat easily falls off the table even when you use a small amount of pressure, it is not a sticky one, and you need to improve its stickiness.

There are many ways to check the ping pong bat’s stickiness. Watch video to figure out!

You can also rub the ball across the surface of the bat. If it is a sticky ping pong paddle, the ball grips onto it.

Drop a ping pong ball on the rubber. If the bounce of the ball is low, the rubber is still tacky. Otherwise, it means the rubber lacks stickiness.

How to make ping pong paddles sticky

Clean the ping pong paddle

Getting your ping pong paddle clean means removing all dust and dirt off the ping pong bat, increasing its adhesion.

If you are wondering about how to clean ping pong paddle, one of the most simple methods is using shaving foam and a soft sponge to clean it gently.

Using water is also a commonly simple way. However, make sure that the sponge is not soaked but just a little wet. Otherwise, it may make the rubber swell, fray, and damaged.

Using butterfly foam

All you need to do is to press to squirt an amount of white foam, smear it on the surface of the ping pong paddle. And after the foam disappears, the rubber will become more sticky and shiny.

However, if these volatile agents are applied to the ping pong paddle too frequently, the performance of the rubber is affected. Professional or advanced players will not use these cleaners.

Using Boosters

All you need is a booster to tune the rubber. I would recommend stickiness boosters like Dandoy Bio Booster.

First, use a brush to apply the glue evenly across the rubber.

Once complete, let it dry for 12 to 24 hours. You can apply another layer if you want your ping pong paddle to be super fast.

Do not use stickiness booster for competitive matches

Remember, this method is for recreational purposes only because ITTF approved tournaments and games have banned boosters.

Using oils

This method is the most effective way to tune your rubbers, improve their stickiness and their lifespan.

First, remove the rubber protection foil from your rubber.

Before using oil, make sure you have cleaned your ping pong paddle.

Take some oil from the kitchen. It can be any kitchen oil such as veggie oil, olive oil, lamp oil, etc. However, sunflower oil is highly recommended to enhance the stickiness of the rubber.

Dip a medium-size brush entirely into the oil and brush your rubber with it.

The soaking will take approximately 30 minutes.

Repeat this from 3 to 5 times. Your rubbers will have a surprisingly good stickiness.

Replacing the rubber

It is a fact that you cannot increase the stickiness of a dead rubber. Once your rubber is dead, it is dead.

It is high time you got to know how to replace ping pong paddle rubber.

However, before replacing it, try some other methods to make the best use of the rubber.

They will save you a considerable amount of money since the rubber is relatively expensive.

Using protective film

After washing the stains, drying the water, and removing the dust, it is the film.

It is recommended to buy some thick film to stick since it is not easy to deform the film.

The general film will be much larger than the rubber surface, so you need to cut it after buying.

My suggestion is to cut it slightly smaller than the rubber surface (the edge should be about 5mm), so it is easier to stick flat and does not need to be deliberately aligned.

Using a plastic protective film is a decent way to increase stickiness

Although it is not easy to open, the edge of the rubber will be better maintained.

If you are looking for perfection, you can cut it with the new rubber as before, so the film will be as big as the rubber. However, it will be very troublesome to align each time it is attached.

The film is generally posted from the bottom. The procedure is similar to sticking the rubber.

From the bottom end of the film, slowly press it with the glue stick to avoid air bubbles or swell.

Remember to put the plastic protective film back on after every time you play.

Using tackiness sprays

However, remember not to use tacky sprays from craft stores. Since these sprays are so sticky, it may make the rubber incredibly dirty when playing.

I would recommend Spinmax as an excellent way to restore as well as to add stickiness to the ping pong paddle.

Using tackiness sprays is simple.

All you need to do is to shake the bottle, lay it to spray on the surface of the rubber.

It takes 20 minutes to dry, but for a complete result, you had better wait for 24 hours to maintain your rubber and significantly extend its lifespan.

To conclude

Adding stickiness to a ping pong paddle is crucial. Not only does it better for your performance but it also saves your money since the rubber is very expensive.

Therefore, before changing a new one and hit the cost, consider using these tips to restore and enhance its stickiness.

Hopefully, the information above is useful to you! Feel free to ask if you have any questions!

Related Video:  Sticky ping pong paddle

Source: Sport Life Z

We will be happy to hear your thoughts

      Leave a reply

      This site uses Akismet to reduce spam. Learn how your comment data is processed.

      Sport Life Z
      Enable registration in settings - general